XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

PRODUCT NUMBER	PRODUCT NAME
69-6	BLACK WATERBASED DTM URETHANE PAINT
GENERAL DESCRIPTION Pruett-Schaffer’s #69-6 Black Urethane is a very fast air-drying, water based, acrylic polyester urethane coating. It is designed as a high gloss, spray applied finish coat for railcar and exterior equipment maintenance applications. It exhibits good film hardness and flexibility, and excellent water, solvent, and abrasion resistance. RECOMMENDED USES This product is recommended for maintenance use as a direct-to-metal over various substrates including cold rolled steel, aluminum, plastics, composites, and existing coatings. It will provide long term, cost effective protection against water, salt, oil, chemicals, and alkali cleaners. SURFACE PREPARATION At a minimum for acceptable performance, surfaces to be coated must be clean and dry, free of oil/grease, loose rust/paint, weld spatter, burning slag, dust, and chalk. Feather all rough or sharp edges. Existing coatings must be tightly adhering. Some well-cured existing coatings may need to be deglossed by sanding or abrasion for this coating to develop its best adhesion; test patches should be made to determine if adhesion is adequate. THINNING Add water slowly with constant gentle agitation to a maximum of 5% by volume. APPLICATION EQUIPMENT Air assisted or airless spray application is preferred. Use a .017-. 020 inch tip. May be applied by brush or roller. Brushes should be of polyester or nylon construction. Rollers should have a nap thickness of ¹/₄ to ³/₈ inch. Apply to 4-8 mils wet film thickness (2-3 mils dry film thickness). DRYING TIME Dries set to touch in 30 minutes and dries hard in 1 hour at 77 ⁰F and		55% R.H. Force drying ovens may be used, do not exceed 250 ⁰F; allow 15 minutes minimum for flashoff of solvent before heating. CLEANUP Clean equipment with room temperature soap and water before the film dries. ENVIRONMENTAL This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It is VOC compliant for the railcar maintenance industry, and contains no chromates, zinc, or free isocyanate. This product complies with current federal regulations regarding the use of lead in paint. PHYSICAL PARAMETERS VOC, ASTM D-3960: 1.49 lb./gal NONVOLATILE: By weight: 45.5 By volume: 42.9 DENSITY, ASTM D-1475: 8.68 lb./gal THEORETICAL COVERAGE: 688 ft²/gallon/mil, dry film INITIAL GLOSS, 60⁰: 85-90 TEST DATA¹ WEATHERING, Gloss retention, %: 1 year Florida exposure: > 80 "B Bulb", ASTM D-4587-91: > 92 Xenon Arc, ASTM G-26-92: > 94 WEATHERING, Color change, Delta E, 1 year Florida exposure: < 2	1000 hr exposures: B Bulb", ASTM D-4587-91: 1.6 Xenon Arc, ASTM G-26-92: 0.9 SOLVENT RESISTANCE, ASTM D-4752: MEK (100 double rubs): pass Toluene (100 double rubs): pass HARDNESS: Pencil, ASTM D-3363: H Pendulum, ASTM D-4366: 166 sec IMPACT RESISTANCE, ASTM D-2794: Direct: >160 in lb Reverse: >160 in lb ABRASION RESISTANCE, Taber, CS-17 wheel, 1000 g, 1000 cycles: 54 mg loss CHEMICAL RESISTANCE, ASTM D-1308: Hydraulic fluid, 24 hr @ 150 ⁰F: no effect Acid, 5% H₂SO₄ pH 0.6, spot: no effect Base, 5% NaOH pH 13.5, spot: no effect Water immersion, 24 hr @ 70 ⁰F: pass 1 typical clear film properties at 7 days air-dry, 70 ⁰F, 50% R.H., 2-mil dry film thickness
THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.

REV. 11-22-2000 PRUETT-SCHAFFER, 3327 STAFFORD STREET, PITTSBURGH, PA 15204

PHONE: (412) 771-2000 FAX: (412) 771-2205