PRODUCT NUMBER

PRODUCT NAME

67-13413

SAFETY YELLOW URETHANE ENAMEL

GENERAL DESCRIPTION

Pruett-Schaffer’s #67-13413 Yellow Enamel is a fast air drying, solvent based, urethane modified alkyd paint. It is designed as a high gloss; brush or spray applied finish coat for a variety of exterior or interior maintenance applications. It exhibits good abrasion and corrosion resistance, color fastness, and exterior durability.

RECOMMENDED USES

This product is recommended for general maintenance use on fabricated steel, masonry and concrete floors, and wood wherever a good quality alkyd finish is needed. It will provide long term, cost-effective protection against water, salt, oil, alkali cleaners, and household chemicals. Use where the ambient temperature will not exceed 300 ^F. Not recommended for immersion service or for areas subject to prolonged chemical solvent exposure.

SURFACE PREPARATION

This product may be used direct-to-metal as supplied. For best results, metal substrates should be blasted to SSPC-SP-6 commercial blast, with a 1-mil blast profile, and primed with a good quality alkyd primer (such as Pruett-Schaffer #30-12620).

Unpainted concrete surfaces should be primed with this material thinned 5-10% with xylol, then recoated within 24 hours with full strength material. All previously painted concrete surfaces should be scraped or sanded to remove all loose coating and to scuff up the surface to provide better adhesion, then washed and allowed to dry completely.

Bare wood surfaces should be primed or coated twice with this paint. Existing coatings must be tightly adhering and deglossed by sanding for best adhesion.

In general, this coating is very tolerant of less than perfect surface preparation, so hand or power tool cleaning may be sufficient for many applications. At a minimum for acceptable performance, surfaces to be coated must be clean and dry, and free of oil/grease, loose rust/paint, weld spatter, burning slag, dust, and chalk. Feather all rough or sharp edges.

THINNING

Under normal conditions no thinning is necessary. Thin with xylol or mineral spirits when using as a primer coat over bare concrete; add a little thinner at a time with constant gentle agitation to a maximum of 10% by volume. If applying to substrates exceeding 90 ^F, use Aromatic 100 thinner.

APPLICATION

May be applied by brush, roller, or conventional airless or air-assisted spray equipment. Brushes should be of polyester or nylon construction. Rollers should have a nap thickness of ¹/₄ to ³/₈ inch. Use a .015-. 020-inch spray tip size. Apply to 3-4 mils dry film thickness (6-8 mils wet) when no primer is used; or 2-3 mils dry film (4-6 mils wet) over primer.

DRYING TIME

Dries tack free in 15-30 minutes at 77 ^F; dry to light handling in 1-2 hours; ultimate cure in 3-5 days. If recoating this material with itself, use within 24 hours or reduced

intercoat adhesion may occur. Force drying ovens may be used, allow 30 minutes minimum for flashoff of solvent before heating.

CLEANUP

Clean equipment with mineral spirits, xylol or toluol before the film dries.

ENVIRONMENTAL

This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It is VOC compliant for the architectural maintenance industry, and contains no lead, chromate, or zinc.

PHYSICAL PARAMETERS

VOC, ASTM D-3960:3.13 lb./gal

WEIGHT PER GALLON, ASTM D-1475:

10.07 lbs.

NONVOLATILE:

By weight: 68.8 +/- 2.0 %

By volume: 52.1 +/- 1.0%

THEORETICAL COVERAGE:

837 ft²/gallon/mil, dry film

INITIAL GLOSS, 60^ , ASTM D-523:

75-80

VISCOSITY, ASTM D562:

63-73 Krebs Units

FLASH POINT, TAG CC:

> 25 ^F, as shipped

TEST DATA

IMPACT, ASTM D-2794:

Direct: > 60 in-lbs. Reverse: > 60 in-lbs.

ANTISAG INDEX, ASTM D-4400:

10 mils

THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.