www.pruett-schaffer.com

PRODUCT NUMBER	PRODUCT NAME
34-13187	CHELSEA BLUE E-SPRAY ENAMEL

GENERAL DESCRIPTION Pruett-Schaffer’s #34-13187 Gray Enamel is a high gloss, air drying, solvent based alkyd paint. It is designed to be spray applied only. #34-13187 exhibits good flexibility, corrosion resistance, and exterior durability. The solvent blend is rich in ketones to improve polarity for electrostatic spray use. # 34 Series QD Enamels may be applied direct-to-metal or over primer. RECOMMENDED USES #34-64 is recommended for general maintenance use on railcars, storage tanks, machinery, and other steel substrates. It is formulated as a good quality high gloss alkyd finish. This coating exhibits exceptional adhesion to a wide variety of substrates including minimally prepared cold rolled steel, forgings, castings, and existing coatings. It is recommended for use over rough surfaces or where extensive surface preparation will not be performed. The high build finish of this paint will hide many of the surface defects which are evident when using a lower solids gloss paint. NOTE: Not recommended for immersion service or for areas subject to severe chemical exposure. SURFACE PREPARATION For severe service, metal substrates should be blasted to SSPC-SP-6 minimum, with a 1 mil blast profile, and primed with a good quality alkyd primer (such as Pruett-Schaffer #30-12620). This coating is very tolerant of less than perfect surface preparation, so hand tool cleaning may be sufficient for some uses. At a minimum for acceptable performance, surfaces to be coated must be clean and	dry, and free of oil, grease, loose rust, loose paint, weld spatter, burning slag, dust, and chalk. Feather all rough or sharp edges. Chalky or dusty surfaces should be power washed and allowed to dry completely. THINNING Under normal conditions no thinning is necessary. Thin if necessary for spraying with xylol or toluol if more polarity is required use MIBK. Add a little at a time with constant gentle agitation to a maximum of 5% by volume. In ambient temperatures over 85 ^0F Aromatic 100 or Aromatic 150 may be used if “dry spraying” occurs. APPLICATION EQUIPMENT May be applied by pressure pot, air-assisted or airless spray. Airless spray gives the best results, use .012-.017 inch tip size.. If applying with a cup type spray gun, thinning may improve application. Apply to 1.5-3.5 mils dry film thickness, or 3-7 mils wet film. DRYING TIME Dries to touch in about 15 minutes @ 1.5 mils DFT. Dry to recoat or stencil in 1 to 2 hours at 77 ^0F. Dry to light handling in 24 hours. Final cure time is about one week. Force drying ovens may be used, allow 30 minutes minimum for flashoff of solvent before heating. CLEANUP Clean equipment with xylol or toluol before the film dries.	ENVIRONMENTAL This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It is VOC compliant for the railcar and architectural maintenance industries, and contains no lead or chromate. PHYSICAL PARAMETERS VOC, ASTM D-3960: 3.31 lb/gal WEIGHT PER GALLON, ASTM D-1475: 9.25 lbs +/- .20 NONVOLATILE: By weight: 64.2 +/- 2.0 % By volume: 52.5 +/- 1.0% THEORETICAL COVERAGE: 842 ft^2/gallon @ 1mil, dry film or 281 @ 3mil INITIAL GLOSS, 60^0 , ASTM D-523: 80 minimum VISCOSITY, ASTM D562: 65-75 Krebs Units FLASH POINT, TAG CC: 25 ^0F TEST DATA IMPACT, ASTM D-2794: Direct: > 40 in-lbs Reverse: > 20 in-lbs ANTISAG INDEX, ASTM D-4400: >9 mils
THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.

QC IDENTIFIER: E26

REVISED 03-02-2005