PRODUCT NUMBER
PRODUCT NAME
30-18
READY MIXED RED OXIDE PRIMER
GENERAL DESCRIPTION
Pruett-Schaffer’s #30-18 Red Oxide Primer is a fast drying, solvent based alkyd paint. It is designed as a brush or spray applied, corrosion preventative metal primer. It is a cost effective general use primer, having good application properties, exterior durability, and superior adhesion and flexibility.
RECOMMENDED USES
This product is recommended for general maintenance use on railcars, storage tanks, machinery, and other steel equipment wherever a standard quality alkyd primer is needed. It exhibits exceptional adhesion to a wide variety of substrates including minimally prepared cold rolled steel, forgings, castings, and existing coatings. This primer is specially recommended for use over surfaces where extensive preparation will not be performed, as the long oil length alkyd formulation of this paint wets rusty and oily substrates efficiently and develops good adhesion. May be used as a primer or tie coat suitable for overcoating with water or solvent based alkyds. The in service temperature limit is approximately 250
0F.This product is not recommended for immersions service, for areas subject to severe chemical exposure, or for use over wood. A test patch to determine compatibility is recommended before top coating with solvent based acrylic, vinyl, epoxy, or urethane coatings as the active oxygenated solvents sometimes present in these coatings may cause newly applied primer to blister or disbond.
SURFACE PREPARATION
For best results, substrates should be blasted to SSPC-SP-6 commercial blast with a 1 mil profile, and all rough areas and sharp edges smoothed. This
coating is tolerant of less than perfect surface preparation however, and hand or power tool preparation such as brushing, sanding or water blasting may be sufficient for many applications. At a minimum for acceptable performance, surfaces to be coated must be clean, dry, free of heavy oil and grease, loose rust and paint, weld spatter, burning slag, dust, and chalk.
THINNING
Under normal conditions no thinning is necessary; if required for proper spraying thin with xylol or toluol. Add a little at a time with constant gentle agitation to a maximum of 5% by volume. In ambient temperatures over 85
0F Aromatic 100 or Aromatic 150 may be used if "dry spraying" occurs.APPLICATION EQUIPMENT
May be applied by brush or airless spray equipment. Airless spray gives the best results, use .015-.020 inch tip size. Brushes should be of polyester or nylon construction. Apply to 3.5-6.0 mils wet film thickness, which yields 1.8-3 mils dry film.
DRYING TIME
Dries tack free in 15-30 minutes, dry to light handling in 1 hour, dry to recoat in 2 hours at 77
0F. Force drying ovens may be used, allow 15 minutes minimum for flashoff of solvent before heating.CLEANUP
Clean equipment with xylol or toluol before the film dries.
ENVIRONMENTAL
This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It is VOC compliant for the railcar and architectural
maintenance industries, and contains no lead, or chromate. Read and understand Material Safety Data Sheet for this product before
using.PHYSICAL PARAMETERS
VOC, ASTM D-3960:3.09 lb/gal
WEIGHT PER GALLON, ASTM D-1475:
12.58 lbs
NONVOLATILE:
By weight: 75.5 +/- 2.0 %
By volume: 53.1 +/- 1.0%
THEORETICAL COVERAGE:
852 ft2/gallon/mil, dry film
INITIAL GLOSS, 60
0 , ASTM D-523:1-5VISCOSITY, ASTM D-562:63-67 Krebs Units
FLASH POINT, TAG CC:50
0F
TEST DATA
IMPACT, ASTM D-2794:
Direct: > 80 in-lbs Reverse: > 80 in-lbs
ANTISAG INDEX, ASTM D-4400:>13 mils
THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.