www.pruett-schaffer.com

PRODUCT NUMBER	PRODUCT NAME
28-69	CLEAR WATER BASED PIPE COATING (LACQUER)

GENERAL DESCRIPTION Pruett-Schaffer’s #28-69 Clear is a very fast air drying, water reducible alkyd paint. It is designed as a spray- or dip-applied, high gloss, exterior finish coat for metal substrates. The cured film exhibits good flexibility and corrosion resistance, abrasion resistance, and high distinctness of image. RECOMMENDED USES This product is recommended as a clearcoat for maintenance coating for equipment and machinery, sheet and tube stock, shelving, axles, bins and tanks. It exhibits good application characteristics and adhesion to a wide variety of substrates including minimally prepared cold rolled steel, castings, forgings, aluminum, and existing coatings. Not recommended for immersion service or for areas subject to temperatures in excess of 300 ^0F. The paint is not flammable and has very low toxicity. SURFACE PREPARATION Apply over primer (follow primer surface preparation instructions) or direct-to-metal. For best results in DTM service, substrates should be blasted to SSPC-SP-6 minimum, with a 1 mil blast profile. Feather all rough or sharp edges. This coating is very tolerant of less than perfect surface preparation however, so chemical cleaning, water blasting, or even hand or power tool cleaning may be sufficient, depending on the level of service required. At a minimum for acceptable performance, all surfaces to be coated must be clean, dry and free of oil/grease, loose rust/paint, weld spatter, burning	slag, dust, and chalk. THINNING Under normal conditions no thinning is necessary or desirable. Thin if necessary for proper spraying with an 80/20 mixture of water/butyl cellosolve (Pruett-Schaffer thinner #98-8937). Add thinner a little at a time with constant gentle agitation to a maximum of 5% by volume. APPLICATION EQUIPMENT This paint may be applied by brush, roller, dip tank application, air-assisted or airless spray. Brushes should be of polyester or nylon construction. Use roller covers with ^3/8 to ^1/4 inch nap. Use spray tips of 0.015-.020 inch. Apply .5 -1 mil dry film thickness if over primer, 1-1.5 mils dry film thickness if direct-to-metal. When using dip tank application, contact Pruett-Schaffer for further information regarding pH and viscosity maintenance requirements of dip tank. DRYING TIME Dries tack free in 15-45 minutes at 77 ^0F and 50% Relative Humidity. Light handling may be possible in 60 minutes. High humidity will prolong dry time more so than low temperatures. To speed the dry time good air movement over the work and local exhaust is recommended. Heat lamps or forced warm air drying will reduce dry time in cold shops. CLEANUP Clean equipment with warm soap and water before the film dries. Run ethyl	alcohol through spray guns after cleaning to prevent corrosion of steel parts. ENVIRONMENTAL This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It contains no lead, chromate, or zinc. PHYSICAL PARAMETERS VOC, ASTM D-3960: 3.30 lb/gal PA VOC: 6.13 lbs/non-volatile gal WEIGHT PER GALLON, ASTM D-1475: 8.40 lbs NONVOLATILE: By weight: 22.9 +/- 2.0 % By volume: 19.9 +/- 1.0% THEORETICAL COVERAGE: 318 ft^2/gallon/mil, dry film INITIAL GLOSS, 60^0, ASTM D-523: 80 MINIMUM VISCOSITY, ASTM D-4212: 40-50 seconds # 2 Zahn Cup pH RANGE, ASTM D-4584: 8.0-9.0 FLASH POINT, PENSKY-MARTINS CC: >142 ^0F TEST DATA SALT SPRAY EXPOSURE, ASTM B-117 and D-1654, 5% SOLUTION: 160 hrs rust creepage from scribe: < 1 mm IMPACT, ASTM D-2794: Direct: > 80 in-lbs Reverse: > 40 in-lbs ELONGATION, ASTM D-522: 1/4 in conical mandrel: no cracking or flaking
THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.

QC IDENTIFIER: E26

REVISED 05-29-2003