PRODUCT NUMBER

PRODUCT NAME

28-110

ATLAS GREEN SILICONE ALKYD WATER BASED PAINT

GENERAL DESCRIPTION

Pruett-Schaffer’s #28-110 Cat Green Paint is an air drying, water reducible silicone alkyd paint. It is designed as a spray- or brush-applied, high gloss, exterior finish coat for metal substrates. The cured film exhibits good flexibility and corrosion resistance, abrasion resistance, high distinctness of image and exterior gloss retention.

RECOMMENDED USES

This product is recommended as a maintenance coating for equipment and machinery, sheet and tube stock, shelving, axles, bins and tanks. It exhibits good application characteristics and adhesion to a wide variety of substrates including minimally prepared cold rolled steel, castings, forgings, aluminum, and existing coatings. Because of its long service life but higher initial cost, it is specially recommended for use where surface preparation and repainting is difficult or expensive. Not recommended for immersion service or for areas subject to temperatures in excess of 400 ^F. The paint is not flammable and has very low toxicity.

SURFACE PREPARATION

Apply over primer (follow primer surface preparation instructions) or direct-to-metal. For best results in DTM service, substrates should be blasted to SSPC-SP-6 minimum, with a 1 mil blast profile. Feather all rough or sharp edges. This coating is very tolerant of less than perfect surface preparation however, so chemical cleaning, water blasting, or even hand or power tool cleaning may be sufficient, depending on the level of service required. At a minimum for acceptable performance, all surfaces to be coated must be clean, dry and free of oil/grease

, loose rust/paint, weld spatter, burning slag, dust, and chalk.

THINNING

Under normal conditions no thinning is necessary or desirable. Thin if necessary for proper spraying with an 80/20 mixture of water/butyl cellosolve (Pruett-Schaffer thinner #98-8937). Add thinner a little at a time with constant gentle agitation to a maximum of 5% by volume.

APPLICATION EQUIPMENT

This paint may be applied by brush, roller, dip tank application, air-assisted or airless spray. Brushes should be of polyester or nylon construction. Use roller covers with ³/₈ to ¹/₄ inch nap. Use spray tips of 0.015-.021 inch. Apply 6-8 mils wet film thickness over primer to achieve approximately 2-3 mils dry film.

DRYING TIME

Dries tack free in 30-60 minutes at 77 ^F and 50% Relative Humidity. Light handling may be possible in 90 minutes. High humidity will prolong dry time more so than low temperatures. To speed the dry time good air movement over the work and local exhaust is recommended. Heat lamps or forced warm air drying will reduce dry time in cold shops.

CLEANUP

Clean equipment with warm soap and

water before the film dries. Run ethyl alcohol through spray guns after cleaning to prevent corrosion of steel parts.

ENVIRONMENTAL

This product meets current air pollution regulations regarding hydrocarbon and ozone reactive emissions. It contains no lead, chromate, or zinc.

PHYSICAL PARAMETERS

VOC, ASTM D-3960:

2.83 lb/gal

WEIGHT PER GALLON, ASTM D-1475:

9.03 lbs

NONVOLATILE:

By weight: 33.2 +/- 2.0 %

By volume: 26.2 +/- 1.0%

THEORETICAL COVERAGE:

422 ft²/gallon/mil, dry film

INITIAL GLOSS, 60^, ASTM D-523:

80-85

VISCOSITY, ASTM D-562:

65-75 Krebs Units

pH RANGE, ASTM D-4584:

8.0-8.5

FLASH POINT, PENSKY-MARTINS CC:

94 ^F

TEST DATA

SALT SPRAY EXPOSURE, ASTM B-117 and D-1654, 5% SOLUTION:

160 hrs rust creepage from scribe: < 1 mm

IMPACT, ASTM D-2794:

Direct: > 120 in-lbs Reverse: > 120 in-lbs

ELONGATION, ASTM D-522:

1/4 in conical mandrel: no cracking or flaking

THIS INFORMATION RESULTS FROM TESTS CONDUCTED IN A LABORATORY UNDER LABORATORY CONDITIONS. DIFFERENT RESULTS MAY BE OBTAINED IN COMMERCIAL USE OF THIS PRODUCT UNDER FACTORY OR FIELD CONDITIONS. PRUETT-SCHAFFER MAKES NO WARRANTY CONCERNING THE SUITABILITY OF THIS PRODUCT FOR THE END USE CONTEMPLATED BY THE BUYER, EXCEPT THAT THE PRODUCT SHALL BE IN COMPLIANCE WITH THE TECHNICAL SPECIFICATIONS PRESENTED HEREIN.